濟南水穩料配比全解析：水泥劑量、骨料級配、含水量控制，一篇文章講明白

　　Full analysis of Jinan water stable material ratio: cement dosage, aggregate gradation, and moisture content control, explained in one article

　　在濟南搞道路工程，水穩料的配比設計直接關系到道路基層的強度和穩定性，是道路質量的關鍵。很多人對水穩料的配比一知半解，導致施工后出現基層開裂、沉降等問題。今天就結合濟南本地的實際情況，給大家詳細講講水穩料的配比設計要點，希望能幫到大家。

　　In road engineering in Jinan, the proportion design of water stable materials is directly related to the strength and stability of the road base, and is the key to road quality. Many people have only a partial understanding of the ratio of water stable materials, which leads to problems such as cracking and settlement of the base layer after construction. Today, based on the actual situation in Jinan, I will give you a detailed explanation of the key points of water stable material ratio design, hoping to help you.

　　首先要明確，水穩料就是水泥穩定碎石或水泥穩定砂礫，它的配比設計主要包括水泥劑量、骨料級配和含水量三個核心要素。這三個要素相互影響，共同決定了水穩料的最終性能。

　　Firstly, it should be clarified that water stable material refers to cement stabilized crushed stone or cement stabilized gravel, and its proportioning design mainly includes three core elements: cement dosage, aggregate grading, and moisture content. These three elements interact with each other and together determine the ultimate performance of water stable materials.

　　水泥劑量是水穩料配比設計的關鍵。水泥劑量過低，水穩料的強度不足，無法滿足道路承載要求；水泥劑量過高，不僅會增加成本，還可能導致水穩料收縮開裂。在濟南，根據道路等級和交通量的不同，水泥劑量一般控制在 3%-7% 之間。對于小區道路、鄉村公路等低交通量道路，水泥劑量可以取 3%-4%；對于城市次干道、支路等中等交通量道路，水泥劑量取 4%-5%；對于城市主干道、快速路等高交通量道路，水泥劑量則需要取 5%-7%。

　　The cement dosage is the key to the design of water stable material ratio. The cement dosage is too low, and the strength of the water stable material is insufficient to meet the road bearing requirements; Excessive cement dosage not only increases costs, but may also lead to shrinkage and cracking of water stable materials. In Jinan, the cement dosage is generally controlled between 3% and 7% depending on the road grade and traffic volume. For low traffic roads such as residential roads and rural roads, the cement dosage can be set at 3% -4%; For medium traffic roads such as urban secondary roads and branch roads, the cement dosage is set at 4% -5%; For high traffic roads such as urban main roads and expressways, the cement dosage needs to be set at 5% -7%.

　　骨料級配也非常重要。骨料的級配是否良好，直接影響水穩料的壓實度和強度。在濟南，水穩料的骨料通常選用當?shù)氐乃槭蛏暗[，要求骨料級配連續均勻，最大粒徑不超過 31.5mm。骨料中粗骨料和細骨料的比例要適當，粗骨料形成骨架，細骨料填充空隙，這樣才能保證水穩料的密實度和穩定性。如果骨料級配不合理，會導致水穩料壓實困難，出現空隙率過大、強度不足等問題。

　　The grading of aggregates is also very important. The good grading of aggregates directly affects the compaction degree and strength of water stable materials. In Jinan, the aggregates for water stable materials are usually selected from local crushed stones or gravel, requiring continuous and uniform gradation of aggregates with a maximum particle size of no more than 31.5mm. The proportion of coarse and fine aggregates in the aggregates should be appropriate, with coarse aggregates forming the skeleton and fine aggregates filling the gaps, in order to ensure the compactness and stability of water stable materials. If the aggregate grading is not reasonable, it will lead to difficulties in compacting water stable materials, resulting in problems such as excessive porosity and insufficient strength.

　　含水量的控制同樣不容忽視。含水量過高，水穩料在碾壓過程中容易出現彈簧現象，無法壓實；含水量過低，水穩料的和易性差，也難以壓實。在濟南，施工時需要根據骨料的含水量和天氣情況，實時調整加水量，使水穩料的含水量接近最佳含水量。最佳含水量可以通過擊實試驗確定，一般來說，水穩料的最佳含水量在 5%-8% 之間。

　　The control of moisture content cannot be ignored either. If the moisture content is too high, the water stable material is prone to spring phenomenon during the rolling process and cannot be compacted; Low moisture content, poor workability of water stable materials, and difficulty in compaction. In Jinan, during construction, it is necessary to adjust the amount of water added in real time according to the moisture content of the aggregate and weather conditions, so that the moisture content of the water stable material is close to the optimal moisture content. The optimal moisture content can be determined through compaction tests. Generally, the optimal moisture content for water stable materials is between 5% and 8%.

　　除了以上三個核心要素，水穩料的配比設計還需要考慮一些細節問題。比如，水泥的品種和強度等級要根據工程要求選擇，一般選用 P.O 42.5 級普通硅酸鹽水泥；骨料的含泥量要嚴格控制，含泥量過高會降低水穩料的強度和穩定性；水穩料的拌合要均勻，確保水泥和骨料充分混合。

　　In addition to the above three core elements, the proportioning design of water stable materials also needs to consider some details. For example, the variety and strength grade of cement should be selected according to the engineering requirements, and P.O 42.5 grade ordinary Portland cement is generally used; The mud content of aggregates should be strictly controlled, as excessive mud content can reduce the strength and stability of water stable materials; The mixing of water stable materials should be uniform to ensure that cement and aggregates are fully mixed.

　　在濟南進行水穩料配比設計時，還要結合當?shù)氐臍夂驐l件和施工工藝。濟南夏季氣溫高，水分蒸發快，施工時要注意保濕養生；冬季氣溫低，水泥水化反應緩慢，要采取保溫措施。同時，施工工藝也會影響水穩料的性能，比如拌合方式、碾壓設備、碾壓遍數等，都要嚴格按照規范要求執行。

　　When designing the water stable material ratio in Jinan, it is also necessary to consider the local climate conditions and construction techniques. Jinan has high summer temperatures and fast evaporation of water, so it is important to pay attention to moisturizing and health preservation during construction; In winter, the temperature is low and the cement hydration reaction is slow, so insulation measures should be taken. At the same time, construction techniques can also affect the performance of water stable materials, such as mixing methods, rolling equipment, and rolling times, which must be strictly implemented in accordance with regulatory requirements.

　　總之，濟南水穩料的配比設計是一個系統工程，需要綜合考慮水泥劑量、骨料級配、含水量等多個因素。只有科學合理地設計配比，并嚴格按照配比進行施工，才能保證道路基層的質量，建設出安全、耐用的道路工程。希望這些建議能幫到在濟南搞道路工程的朋友們，祝大家施工順利！

　　In summary, the proportioning design of water stable materials in Jinan is a systematic project that requires comprehensive consideration of multiple factors such as cement dosage, aggregate gradation, and moisture content. Only by scientifically and reasonably designing the ratio and strictly following the ratio during construction, can the quality of the road base be guaranteed and a safe and durable road project be constructed. I hope these suggestions can help friends who are engaged in road engineering in Jinan. I wish everyone a smooth construction!