公司新聞
瀝青混凝土路面現場熱再生
來源：http://www.seatostar.com/ 日期：2023-08-10
就地?zé)嵩偕哼@種再生法就是利用瀝青路面熱再生聯合機組來就地完成瀝青路面的熱再生修復。原有路面材料100％地利用，不需要搬運廢料及廢棄物堆放場地，可減少環境污染；能夠改變個別 的混合料成分，以便給定瀝青 混合料的最佳配比；可以快速就地再生，并隨著工程進度開放道路交通，對交通干擾最小，現在國外應用很廣。
On site geothermal regeneration: This regeneration method utilizes a combined unit of asphalt pavement thermal regeneration to complete on-site thermal regeneration and repair of asphalt pavement. The original road materials are 100% utilized, and there is no need to handle waste materials or waste storage sites, which can reduce environmental pollution; Being able to change individual mixture components in order to give the optimal ratio of asphalt mixtures; It can quickly regenerate on site and open up road traffic as the project progresses, with minimal traffic interference. It is now widely used abroad.
瀝青路面的現場熱再生就是原有瀝青路面再生100％在現場完成，先加熱軟化原瀝青路面以便于耙松，然后將耙松的瀝青路面充分拌和，隨后進行攤鋪碾壓。
The on-site thermal regeneration of asphalt pavement refers to the 100% completion of the original asphalt pavement regeneration on site. The original asphalt pavement is first heated and softened to facilitate loosening, and then the loosened asphalt pavement is fully mixed, followed by paving and rolling.
瀝青路面的老化主要是其瀝青中輕質組分減少，石料的少量損失，瀝青路面就地?zé)嵩偕ㄟ^添加再生劑調節舊瀝青路面中老化瀝青的化學組分，來恢復老化瀝青的性能，同時補充少量新拌瀝青混合料來調整原有瀝青混合料級配，以達到瀝青路面再生效果。
The aging of asphalt pavement is mainly due to the reduction of lightweight components in its asphalt and a small amount of loss of stone materials. The thermal regeneration of asphalt pavement is achieved by adding regenerants to adjust the chemical components of aging asphalt in the old asphalt pavement, in order to restore the performance of aging asphalt. At the same time, a small amount of fresh asphalt mixture is added to adjust the grading of the original asphalt mixture, in order to achieve the effect of asphalt pavement regeneration.
新瀝青混合料和再生劑按需要比例加入。通常新瀝青混合料控制在再生混合料質量的30％以內。各種材料的添加率根據原瀝青路面性能分析及其實驗室配合比設計，并符合相應的混合料規范而確定。
Add new asphalt mixture and recycling agent in proportion as needed. Usually, new asphalt mixtures are controlled within 30% of the quality of recycled mixtures. The addition rate of various materials is determined based on the performance analysis of the original asphalt pavement and its laboratory mix design, and in accordance with the corresponding mixture specifications.
依據所使用的工藝可將現場熱再生細分為三種，即耙松整形再生、重鋪再生和復拌再生。
According to the process used, on-site thermal regeneration can be divided into three types, namely raking and shaping regeneration, re laying regeneration, and re mixing regeneration.
耙松整形再生：先用加熱設備把瀝青路面烤熱軟化，然后用設備本身自帶的耙松裝置將路面耙松整形，同時添加再生劑，然后用壓路機碾實 。
Raking and shaping regeneration: First, use heating equipment to heat and soften the asphalt pavement, and then use the equipment's own loosening device to loosen and shape the pavement. At the same time, add regeneration agent, and then use a roller to compact it.
重鋪再生：先用加熱設備把瀝青路面烤熱軟化，接著銑刨舊瀝青層，不同的是將銑刨下來的瀝青料直接進行攤鋪，緊接著在其上面再攤鋪一層新的瀝青混合料，然后用壓路機碾實。
Re paving and regeneration: First, use heating equipment to heat and soften the asphalt pavement, then mill the old asphalt layer. The difference is that the milled asphalt material is directly spread, and then a new layer of asphalt mixture is laid on top of it, and then compacted with a roller.
、復拌再生：先用加熱設備把瀝青路面烤熱軟化，再用銑刨機銑刨舊瀝青層，然后按一定比例添加再生劑再添加用來調整集配的新料，攪拌后將混合料收集排放到攤鋪機上進行攤鋪，最后用壓路機碾實。
Re mixing and regeneration: First, use heating equipment to heat and soften the asphalt pavement, then use a milling machine to mill the old asphalt layer, and then add a certain proportion of regeneration agent before adding new materials for adjusting the mixing. After mixing, collect and discharge the mixture onto the paver for paving, and finally use a roller to compact it.
★現場熱再生的優點：
Advantages of on-site thermal regeneration:
通過再生現有材料就地修復路面；
Repair the road surface in situ by recycling existing materials;
一次性完成再生加鋪；
Complete regeneration and paving in one go;
快速、經濟、環保性強、節約原材料；
Fast, economical, environmentally friendly, and material saving;
成本低：對工期、運輸費用、能源和原材料綜合成本降低20～50％；
Low cost: reduces the overall cost of construction period, transportation costs, energy, and raw materials by 20-50%;
施工時間短，開放交通快，對公共交通的影響很小；
Short construction time, fast open traffic, and minimal impact on public transportation;
可完成再生加鋪、重鋪、重新整型等施工；
Capable of completing construction such as regeneration, resurfacing, and reshaping;
消除了傳統方法固有的處理問題。
Eliminates the inherent processing issues of traditional methods.
接縫及層間均熱粘結。
Joint and interlayer thermal bonding.
極大減少了舊材料、新材料的運輸量；
Greatly reducing the transportation volume of old and new materials;
再生現有的路面材料，就地修復路面；
Regenerate existing road materials and repair the road surface on site;
★現場熱再生的缺點：
Disadvantages of on-site thermal regeneration:
再生深度通常最大為 6cm；
The maximum regeneration depth is usually 6cm;
無法除去已經不合適進行再生的舊混合料，級配調整幅度有限；
Unable to remove old mixtures that are no longer suitable for regeneration, and the adjustment of gradation is limited;
無法解決軟弱路基和基層的問題。
Unable to solve the problem of weak roadbed and base layer.
本文由濟南瀝青料友情奉獻.更多有關的知識請點擊:http://www.seatostar.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待
This article is dedicated by Jinan Asphalt Materials. For more information, please click on: http://www.seatostar.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：